Torque specs for arp rocker studs

2019-09-20 00:18

Aug 08, 2009 Studs are never supposed to be torqed into the block, just installed finger tight. As far as the nut torque spec, go to ARP's site and look it up, they are all different depending on the size, length and style of the stud.Oct 10, 2008 Rocker Stud Torque Specs# 1 Post by hugger73hatch Mon Sep 15, 2008 3: 37 am I was wondering what to torque the rocker arm studs to. I can't quite remember, but for some reason I am thinking 50 ft lbs. The heads are Dart Iron Eagle Platinum with 716 studs. Thanks. torque specs for arp rocker studs

ARP High Performance series rocker arm studs are ideal for ET bracket racing, limited rule oval track competition, or street use. Made from 8740 chromoly steel and are heattreated to 180, 000 psi tensile strength, they are concentric within. 005 T. I. R. thread pitch to thread pitch, which will give you more consistent rocker geometry.

516 Rocker Arm Stud Kit (except LS7) Rocker Arm Stud Kit. Installed Height: ARP Stainless Valve Cover Bolt Kit. Chevrolet Gen IIIIV LS Series small block, with 0. 375 spacer, hex, ARP Stainless Valve Cover Bolt Kit. Chevrolet Gen IIIIV How can the answer be improved?torque specs for arp rocker studs Jul 31, 2010 Re: Rocker Arm Stud Torque Specs Help please Reply# 12 on: July 30, 2010, 04: 04: 16 pm You will see alot of times, you can simply put a 716 arp head bolt washer under each stud to give you the needed minimum.

Torque specs for arp rocker studs free

Sep 04, 2012 Harden heat treated chrome moly pushrods are required with guideplate style heads. Rocker arm studs should be torqued to 60 ft. lbs. they are not torqued from AFR, torque pedestal rocker arms to stock recommendation. torque specs for arp rocker studs Inner and Outer bolts: Engine Oil: 110 ftlbs. 38 Connecting Rod Cap: Engine Oil: 50 ftlbs. 716 Connecting Rod Cap: Engine Oil: 70 ftlbs. Cylinder Heads: Engine oil (blind hole) Sealer (water jacket) 75 ftlbs. (long bolts) 65 ftlbs. (short bolts) Rocker Studs (screwin) Engine Oil: 50 ftlbs. in) Oil Pump: Engine Oil: 65 ftlbs. Oil Pan: Engine Oil: 12 ftlbs. 45 kits found for Rocker Arm Studs ARP rocker studs are concentric within. 005, extralarge radius base offers greater resistance to flex. NOTE: To be used ONLY with ARP The rocker studs that come with them need 30 footpounds of torque with oil and 20 footpounds of torque with ARP lube. The cylinder head studs with part no. HSBM70, HSC4201, HSC4301, HSC4601, HSC48, HSCB4601, HSGT6, HSL68, and HSRV45 require 85 footpounds of torque with oil and 70 footpounds of torque with ARP lube. lubricate the studs with ARP Thread Sealer. [5 Install the push rod guide plates (if applicable). [6 Screw the rocker arm studs into the cylinder head and tighten them hand tight. Make sure the bottom side of the hex is seated down against the cylinder head or guide plate (where applicable). [7 Tighten the rocker arm studs to the following specifications: PRELOAD (TORQUE) RECOMMENDATIONS Aluminum

Rating: 4.92 / Views: 473